- Home
- Optical Transceivers
- Finisar (Coherent)
- 400G
- FTCD4313E2PLL
Actual product photos
available on request
To keep listings accurate, we share real photos of the exact FTCD4313E2PLL stock you will receive, including the label, serial number and packaging.
Request photos from our teamPhotos are usually shared within working hours on WhatsApp or email.
Finisar FTCD4313E2PLL 400GBASE-FR4 QSFP-DD 1310nm CWDM4 2 km
400 Gb/s 400GBASE-FR4 QSFP-DD transceiver, 1310nm CWDM4, up to 2 km.
- Manufacturer
- Coherent Corp. (formerly Finisar / II-VI)
- Mfr part number
- FTCD4313E2PLL
- Family
- FTCD4313
- Category
- Fiber optic transceiver modules
- Datasheet
- FTCD4313E2PLL datasheet (PDF)
FTCD4313E2PLL specifications
| Attribute | Value |
|---|---|
| Manufacturer | Coherent Corp. (Finisar) |
| Manufacturer part number | FTCD4313E2PLL |
| Product family | FTCD4313 |
| Form factor | QSFP-DD |
| Standards / application | IEEE P802.3cu 400G-FR4; portions of P802.3bs; QSFP-DD MSA; QSFP28 MSA |
| Data rate | 425 Gb/s (4x 53.125 GBd PAM4 optical; 8x50G PAM4 400GAUI-8 electrical) |
| Wavelength | 1264.5–1277.5, 1284.5–1297.5, 1304.5–1317.5, 1324.5–1337.5 nm |
| Laser | 4-lane CWDM (Class 1) |
| Receiver | PIN |
| Reach | 2 km on SMF (G.652) |
| Connector | Duplex LC |
| Tx output power | −3.2 to 4.4 dBm per lane |
| Rx sensitivity | −4.6 dBm OMAouter (SECQ < 1.4 dB) |
| Rx overload / max input | 4.4 dBm avg receive power; 5.4 dBm damage threshold |
| Extinction ratio | 3.5 dB min |
| Supply voltage | 3.3 V (3.135–3.465 V) |
| Power dissipation | < 11 W c-temp / < 10 W limited temp (E2); < 8 W (E3) |
| Operating temperature | 0 to 70 °C case (C); +20 to +60 °C (L, limited temp) |
| Diagnostics | I2C management interface |
| Compliance | RoHS-6 |
| Lifecycle | Ask for availability |
| Variant note | Gen 2, limited temp, < 10 W |
Optical and electrical values are from the Finisar / Coherent family datasheet; temperature grade is per part number. Confirm critical values with us before ordering.
About the Finisar FTCD4313E2PLL
The Finisar FTCD4313E2PLL (now a Coherent Corp. product, formerly II-VI) is a QSFP-DD 400GBASE-FR4 optical transceiver for 400 Gb/s links at 1310nm CWDM4 over Duplex SMF, LC, with reach up to 2 km. It belongs to Finisar's FTCD4313 family, which has 4 orderable variants that differ by temperature grade, latch, receiver build or wavelength channel. Typical uses: 400G data-centre spine, AI/ML clusters and 400ZR / ZR+ coherent DCI.
- Hot-pluggable QSFP-DD type 2 form factor
- Supports 425Gb/s aggregate bit rate
- 4x100Gb/s PAM4 serial lanes
- 8x50G PAM4 retimed 400GAUI-8 electrical interface
- LC duplex receptacle
- I2C management interface
FTCD4313E2PLL: frequently asked questions
What is the Finisar FTCD4313E2PLL?
The FTCD4313E2PLL is a Finisar QSFP-DD transceiver for 400GBASE-FR4 at 400 Gb/s. Finisar is now part of Coherent Corp. (formerly II-VI), and the part number is unchanged. It is used for 400G data-centre spine, AI/ML clusters and 400ZR / ZR+ coherent DCI.
What is the maximum distance of the FTCD4313E2PLL?
The FTCD4313E2PLL is specified for up to 2 km over Duplex SMF, LC. Long-reach optics may need an attenuator on short links; we can advise based on your link loss.
What is the optical power budget of the FTCD4313E2PLL?
Per the Finisar family datasheet, the FTCD4313E2PLL transmits −3.2 to 4.4 dBm per lane and has a receiver sensitivity of −4.6 dBm OMAouter (SECQ < 1.4 dB). Maximum receiver input is 4.4 dBm avg receive power; 5.4 dBm damage threshold.
Does the FTCD4313E2PLL support DDM / digital diagnostics?
Yes. I2C management interface. Your switch can read live temperature, voltage, laser bias and Tx/Rx power.
Which fiber and connector does the FTCD4313E2PLL use?
The FTCD4313E2PLL works at 1310nm CWDM4 over Duplex SMF, LC. CWDM/DWDM optics must match the channel of your mux/demux port. Both ends of a link must use the same optical standard.
Will the FTCD4313E2PLL work in my Cisco, Juniper, Arista or HPE switch?
The FTCD4313E2PLL follows the QSFP-DD MSA, so it fits any matching port. It carries Finisar's own EEPROM programming; switches that check the module vendor may need a configuration setting or a vendor-branded optic. Send us your switch model and we confirm before dispatch.
FTCD4313E2PLL vs FTCD4313E3PCL: what is the difference?
Both are in Finisar's FTCD4313 family. They differ in build / application (400GBASE-FR4 vs 400GBASE-FR4 Gen3). Pick the variant that matches your temperature, latch and wavelength needs.
What does the FTCD4313E2PLL part number mean?
The FTCD prefix marks Finisar's 400G family. The remaining characters identify the optical design and build variant.
Is your FTCD4313E2PLL genuine Finisar?
Yes. Next Gen Networks supplies original Finisar / Coherent modules, not third-party lookalikes or grey-market stock, and shares serial numbers on request.
What is the FTCD4313E2PLL price in India and how do I order?
The Finisar FTCD4313E2PLL price in India depends on quantity, delivery city and current stock. Next Gen Networks supplies it with a GST invoice (input tax credit ready) and pan-India dispatch from New Delhi. Send the part number, quantity and delivery city on WhatsApp +91-7827955775 or email Sales@nextgennetworks.in for a GST quote.
What power does the FTCD4313E2PLL need?
It runs from 3.3 V (3.135–3.465 V) with power dissipation of < 11 W c-temp / < 10 W limited temp (E2); < 8 W (E3).
Documents
NextGen datasheetPDF · specs, FAQ & buying guideManufacturer datasheet
Finisar / Coherent family datasheet
Related Finisar parts
FTCD4313E2PCL400GBASE-FR4, 2 kmFTCD4313E3PCL400GBASE-FR4 Gen3, 2 kmFTCD4313E3PLL400GBASE-FR4 Gen3, 2 kmFTCD4323E3PCL400GBASE-LR4-10 Gen3, 10 kmFTCD4523E2PCM400GBASE-DR4, 500 mFTCD4533E2PCM400G DR4+ / 4x100G-FR1, 2 kmGovernment, PSU and enterprise orders welcome. GST invoice and pan-India delivery.
Talk to Sales